Round Two - First Success, with Holo

If you read my first post (this would be my second), then you know all about the crappily casted figure I had for my cherry kit. So with the first time, and all the mistakes usually involved, out of the way, it was time to move on to number two.

I mentioned in my last post that I purchased five figures from two Ebay sellers - but that's not true - because I forgot about a sixth figure purchased from a third seller. This sixth figure, unlike the other five, ended up being from a e2046-like seller - one which knew WTF they were doing and produced a kit which is as good as the original. I tried to find the seller, or the source of the figure, to no avail - so I don't know who to thank, or more importantly, who to buy some more from.

About the figure. This time, instead of using acrylics, because there was much more fading and gradient in this figure, I decided to use oil paints. So all the lessons I learned during this figure were about using oil paints. Except one.

Lesson 3: Using the oven to reshape the PVC

The first figure, as well as the third, were both RESIN. Which I am told does not reshape so easily. But this figure was good ol' PVC, so I accidentally discovered that I could reshape (bend it) by sticking it in the oven on 150F for a few hours. I'm sure I could have turned it up higher but I didn't want an accident. But it was super simple, and at that temperature, there was no "melt", where small pieces get really out of shape. So pop it in, take it out, bend it.

I say that this was an accidental discovery because I didn't stick it in the oven to bend it. I stuck it in the oven to dry the oil paint.

Lesson 4: Dry the oil pain in the oven overnight

Because I used oil paints on this figure, I discovered that even after three days in the open, the paint remained "wet". I read a bit later that this is actually a feature of oil paints - painters don't have to rush. And it's true, acrylics dry way too fast, but I'd say a few days is a bit slow. I can't image how long this figure would have taken if I had to wait a week for the pain to dry. So I did a little research, and found out that heat would make it dry faster. So I took the risk, put the oven on low, 150F, and left the figure's leg in the oven overnight. And low and behold, the next day, full 24 hours later, I take it out and it was dry as a bone. Excellent!

Following that little discovery, I was able to move fast and get the figure base layer done. If you didn't know, I like painting a base coat on all the figures, over which I paint on a second layer which would include any fading, shading, or gradients. There's an occasional third layer for the small bits or the accessories. The body, the bag, the apples, the hair, and the tail were all rather straight forward. I did mess up on the tail and have to redo it, but again it wasn't tricky.

Lesson 5: Dry wipe (oil)

Watching youtube, I discovered a technique I liked and tried to great success in this figure: the dry wipe. Basically, I pain a base layer, dry it, then paint a top layer, and wipe it off lightly soon afterwards. I did this for the boxes and the apples in the boxes (even though you can't really see them ... a lot of effort for bits you can't even see). I like it so much I tried to redo the bag with the technique, and it turned out ok, but wasn't near as good.

Lesson 6: Acrylic dry wipe 

It worked sooo well, I wondered what would happen if I used acrylic to the same affect. I noticed that the oils created a fairly thick color difference with the dry wipe, and I thought that acrylics would be able to produce something similar but with a thinner color. As it turns out, I was right, but boy did I come close to messing it up. As you know, acrylics dry fast, but I was not prepared for just how fast they would dry before they just wouldn't wipe off at all! So the wipe affect didn't work near as well, but it turns out, it was exactly what I needed. With acrylics, apparently the thicker areas wipe off better, since the medium has takes longer to evaporate, whereas the thinner areas dried faster and just wouldn't wipe off unless I wiped within a few seconds. Anyway, you can see for yourself - the stones were done with a base coat of black acrylic, a top coat of grey oil paint, and a highlight using the wipe method with a white acrylic paint. I made the middle layer of grey oil paint because I thought it would help keep the white acrylic from drying so fast - turned out that it didn't work.

Introduction and Black Rock Shooter

First post

So, I've been painting garage kit anime figures for about a year off an on. I've learned a lot since starting. Some lessons have been obvious, some you just have to learn through practice. I thought that I'd share my experiences and my lessons. Also, I want to brag a little be because I've spent untold hours on these figures - sometimes to ultimate disappointment.

I started out by accident. I was purchasing a pvc figure on ebay, when a few days after I order it I realize that it's a garage kit - meaning I have to paint it myself. I of course read that it was a "GK" but I had no idea what that meant when I purchased it. But instead of returning it, I decided what the hell, why not just paint it. I'm not a stranger to painting in general - I took seven years of classes from the ages of 11 to 18 in the public school system. That doesn't mean I was any good at it though. And in this new born enthusiasm for an accidental hobby, I decided it would be more efficient to purchase several of the kits - that way the cost of the paints could be spread out over multiple figures instead of just one. So, I decide to buy 5 total garage kit figures from two different Ebay sellers for around $35 each.

First Mistake - Buying from Ebay

One after another the kits started to arrive. But I was distracted by life in general, and didn't get around to actually painting them for about two months. That was my second mistake - I didn't inspect the goods. So I open the first kit and get to work. The first thing I notice was that the figure had many points on it where it needed sanding or cutting. I had read that a little work to get the figure in good condition was commonplace, so I didn't worry initially. I soon found that some of the pieces were irreparably disfigured. But I didn't know that I wouldn't be able to fix it before I started, so I got to work and spend the first dozen or so hours on my first figure, trying to get the round peg in the triangle hole. I was able to repair things enough to work (not look good, but work), all except for one piece which was part of the cape, which had about a centimeter gap between what was, and what should have been. In the end I pasted the bits together and got my glue gun out to fill the hole. At this point I'm about 20 hours into the project, just making the bits fit together. Surely if I didn't spend so much money, I would have just tossed the thing and called it a day. The worse part, looking back, was that I could not warn other Ebayers about the crappy seller because I had waited more than 60 days and you can't leave feedback after that.

As it was, I got my spray paint out and started on the monotone bits of the figure. Fortunately, a large part of the figure is pure black. Those bits, while they didn't fit together, were easy enough to paint. I actually bothered to wash all the bits and put a base primer coat on them, so I haven't had a problem with paint chipping on that figure. The body was my first jaunt into acrylics in a while. I knew they had a tendency to leave brush stroke imprints in the paint, but I figured I could be careful. So I tried and I tried, but god damn if I didn't leave brush strokes everywhere. All in all it wasn't so bad, and I even shaded the torso pretty good for my first time. As long as you stood far enough away, it looked acceptable. The hair was a bitch to glue on, since the pieces were thin and didn't fit together (nothing on this figure fit together, btw). And there was an earthquake a few months later where the figure fell and basically all the hair pieces went flying. But again, step back far enough and you can't even tell.

So after all was said and done, and after about 50 hours (only half of which was spent actually painting), this is what I ended up with:

Black Rock Shooter

You'll notice there's no eyes. That's basically because by the time I got to that part, I was burnt out. I mean, you can only give a figure so much time before you get sick just looking at it. That was me. So instead of doing a half-ass job and regretting it, I decided to just finish and let it sit till some day when I decided it was time.

You'll notice a gleam on the skin - that's be cause I sprayed a protecting coat of gloss enamel on it - which I wasn't sure about at the time but ended up being a good idea. You also might notice the matte hair compared to the glossy coat. Or maybe the albino coloration instead of just fair skin - so much more pink and white instead of orange or peach. Also, this is one of my better skin shading jobs - the torso around the scar, the abs, the ribs, and the cheek, ears, and chin. Really, I haven't gone through that much effort since my first two figures.

Those zippers look frikin awesome considering how crappily they were casted. I've no idea how much time I spent just cutting out zipper bits - as the cast melded them all together.

Please ignore the sexy looking thing behind the figure - she lost her skirt and is terribly embarrassed.

Lesson 2 - Don't be afraid to take a step backwards

Now, you'd think that after shaping the bits, cutting them, painting them, and gluing them together, that I'd be done. And you'd be wrong. Due to the fact that all the parts were misshaped, the figure is horribly off balance. She basically needs to be glued to a wider base to maintain balance. Which is what I did. Till an earthquake hit and she fell over and broke several hair bits off and broke her wrist with the sword. So, having to glue these parts back on anyway, I decided to finally fix her balance. It actually wasn't all that hard - I just had to rip her off the base and glue her in a different direction. What you see in the pics is after the fix: a perfectly balanced figure. So the lesson was, I know it's annoying, but when you need to take a step back, you need to take a step back. Don't try to ignore it because you'll only regret it.

I guess that's all for now. I think I'll make a post per figure, which means, on to number two!!